Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
General information
Care of a body
Care of the panels of furnish made of vinyl
Care of an upholstery and salon rugs
Repair of insignificant damages of body panels
Repair of considerable damages of a body
Service of loops and locks
Replacement wind and motionless glasses
Removal, installation and adjustment of provision of a cowl
Removal and installation of the lock of a cowl and cable of its drive
Removal and installation to the place of the panel of a decorative front grille
Removal and installation of a forward wing
Removal and installation of bumpers
Removal and installation of the panel of an internal upholstery of a door
Removal, installation and adjustment of provision of a door
Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
Removal and installation of a windowpane of a door
Removal and installation of a regulator of a window of a door
Removal and installation of the central console
Removal and installation of the panel of an upholstery of a door of a back
Removal, installation and adjustment of provision of a door of a back
Replacement of an emphasis of a door of a back
Removal and installation of facing of a combination of devices
Removal and installation of facings of a control panel
Removal and installation of a control panel
Removal and installation of covers of a casing of a steering column
Removal and installation of rear-view mirrors
Remove also installation of a lattice of a fairing
Removal and installation of seats
Control body sizes
+ System of onboard electric equipment
+ Governing bodies and operation receptions
|
Removal, installation and adjustment of provision of a cowl
|
|
The cowl is rather heavy element of a body and installation represents it sufficient difficult procedure. Removal and installation of a cowl it should be made by strengths of at least two people. |
Removal and installation
|
|
- For protection in the course of removal of a cowl of the painted surfaces of a fairing and wings of the car cover them with blankets and whether covers specially let out for this purpose.
- Mark the provision of loops concerning a car body for a guarantee of the correct installation of a cowl at assembly (use a chertilka, a marker or easily washing away paint).
- Disconnect all disturbing to cowl removal cables and wires.
|
|
- Before removal of a cowl disconnect from it a plait of wires of a lamp of illumination of an impellent compartment.
|
- By means of the assistant who will support a cowl, give nuts of fastening of loops to it.
- Lift a cowl.
- Installation make upside-down.
|
|
Adjustment
|
|
- Longitudinal and cross-section adjustments of provision of a cowl in an aperture of an impellent compartment are carried out by shift it concerning plates of loops after preliminary weakening of bolts of their fastening.
- For an assessment of size of shift of a cowl lead round plates of loops.
- Weaken fixing nuts and displace a cowl (not on many for each approach), as appropriate correcting its situation. Tighten fixing nuts (or bolts), carefully close a cowl and check correctness of its situation.
- Adjust the provision of shock pillows on a radiator support so that the cowl when closing appeared aflush with the top panels of wings.
- The provision of assembly of a clamp of the lock on a cowl also can be adjusted in the longitudinal or cross-section directions after weakening of fixing bolts.
- The lock, also as well as loops, should be greased regularly with white greasing on a lithium basis in order to avoid a souring and service life extension (decrease in speed of wear).
|
|
|
|
