Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   General information
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages of body panels
   Repair of considerable damages of a body
   Service of loops and locks
   Replacement wind and motionless glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of the lock of a cowl and cable of its drive
   Removal and installation to the place of the panel of a decorative front grille
   Removal and installation of a forward wing
   Removal and installation of bumpers
   Removal and installation of the panel of an internal upholstery of a door
   Removal, installation and adjustment of provision of a door
   Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
   Removal and installation of a windowpane of a door
   Removal and installation of a regulator of a window of a door
   Removal and installation of the central console
   Removal and installation of the panel of an upholstery of a door of a back
   Removal, installation and adjustment of provision of a door of a back
   Replacement of an emphasis of a door of a back
   Removal and installation of facing of a combination of devices
   Removal and installation of facings of a control panel
   Removal and installation of a control panel
   Removal and installation of covers of a casing of a steering column
   Removal and installation of rear-view mirrors
   Remove also installation of a lattice of a fairing
   Removal and installation of seats
   Control body sizes
+ System of onboard electric equipment
+ Governing bodies and operation receptions

0ea6cc78 0ea6cc78

Removal and installation of bumpers

See the prevention at the beginning of the Section Removal and installation to the place of the panel of a decorative front grille.

The forward

 PERFORMANCE ORDER

  1. The front bumper on cars of these models consists of the bottom facing and the cross-section beam welded on a frame which is actually playing a role of a bumper. Disconnect a negative wire from the battery and remove the front grille panel (The section Removal and installation to the place of the panel of a decorative front grille).
  2. Remove assemblies of the right and left head block headlights, lateral marker lights and indexes of turns (Head System of onboard electric equipment).
  3. Remove clamps of facing of a front bumper.
  1. Remove the top and bottom clamps of the panel of facing of a bumper.
  1. Remove plastic rivets from a forward part of loker of wings.
  1. Remove clamps of fastening of loker of wings to bumper facing.
  1. Remove bumper facing from fixing pins, having used a small screw-driver for an otpuskaniye of lock uvulas under support of indexes of turns.
  2. Installation make upside-down.

The back

 PERFORMANCE ORDER

  1. To Poddomkratta a car back also establish it on props.
  2. On the models equipped with the hook-on device (turnbuckle), disconnect electroconducting, then, holding a turnbuckle, give fixing nuts and omit assembly on the earth.
  1. Before removal of a rear bumper it is necessary to remove assembly of the hook-on device.
  1. Holding a bumper, remove clamps of loker of wings.
  2. Give fixing bolts of arms and remove a bumper beam with the facing panel from the car.
  1. Give bolts of an arm of a bumper.
  1. Remove basic arms from a bumper.

Details of installation of a rear bumper.

  1. Installation make upside-down.