Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
- Governing bodies and operation receptions
   Acquaintance to the car
   Start of the engine and driving
   Dashboard and salon equipment
   Trailer towage
   Emergency towage of the car
   Car towage for the purpose of engine start


0ea6cc78 0ea6cc78

Governing bodies and operation receptions

Acquaintance to the car

Keys, locks and locks

Set of keys

The set of keys which is given out upon purchase of the new car is packed into a plastic cover, with the number code put down on it. If you receive keys without such packing, ask the representative of dealer office where the car is acquired to tell you a number code of keys.

Two keys enter into a set - main and office. The main key approaches to all locks on the car whereas the office is intended only for unlocking/locking of a driver's door and management of the ignition lock. The main key should be stored constantly at the owner of a vehicle whereas the office can be transferred to parkovshchik of parkings or masters of car-care center who cannot get with its help even into a ware box of the dashboard.

Main key (at the left) and office key (on the right).

Key introduction in the lock of ignition and its extraction back

Do not forget before leaving the car to take a key from the ignition lock. Check, whether all doors are reliably locked!

The key is equipped with a bilateral small beard and can be inserted into the lock in any way. Enter a key against the stop into a well of the cylinder of the lock of ignition and turn it in demanded of designated on an accompanying illustration situation. Key introduction in the lock and its extraction are back possible only in the position LOCK of the cylinder. For transfer of the key inserted into the lock to the situation LOCK previously press it (the lever of the AT selector should be established in situation P).

Positions of the cylinder of the lock of ignition.

If to open a driver's door at inserted into the ignition lock a key, the alarm buzzer reminding to the driver of need to take a key will be distributed.

Blocking of a steering column

The car is equipped with a blokirator of a steering column of passive type. Blokirator prevents driving possibility at taken of the ignition lock a key. If the steering wheel turns no more than on a half of turn in each of the directions, and the key is taken from the ignition lock, therefore the steering column is blocked.

To make wheel blocking, turn it the top party down, muffle the engine and take a key from the ignition lock. Now slightly pull a steering wheel, rotating it in both directions for blokirator input in gearing.

Shutdown of a blokirator is made by small turn of a key in the ignition lock in any of the parties.

If blocking of a wheel was made by a way of its turn to the right/to the left, and for its shutdown the steering wheel should be turned in the same direction.

Locks of doors

The main key except the lock of ignition approaches also to all doors of the car, including a back door.

To unlock or lock a door, enter a key into a well of the cylinder of its lock.

The main key approaches to locks of all doors of the car.

After unlocking of the lock of a door of a back it can repeatedly open and be locked without key application. To open a back door, pull on itself its handle.

At leaky closed door of a back the fulfilled gases containing highly toxic and hazardous to health and human life monooxide of carbon (WITH) get into car salon during its movement! Before beginning movement make sure of reliability of closing of a door of a back.

Otpuskaniye of the lock of folding glass of a door of a back (can enter into an additional complete set of the car) is made at the same time with unlocking of the last. For opening of glass wring out top a rychazhok of the switch located over a plate of registration plate. When opening folding glass there is an automatic shutdown of a back screen wiper for the purpose of prevention of its casual start.

Handle of unlocking of the lock of a door of a back (the top arrow) and rychazhok of the switch of an otpuskaniye of a clamp of folding glass of a door of a back (the bottom arrow).

At leaky closed folding glass of a door of a back the fulfilled gases containing highly toxic and hazardous to health and human life monooxide of carbon (WITH) get into car salon during its movement! Whether before beginning movement check densely glass is closed.

All doors of the car are equipped with internal locks of rychazhkovy type. For door locking at a zakhlopyvaniye it is enough to transfer forward to the situation LOCK the rychazhkovy switch on its internal party.

For automatic locking of a door at its zakhlopyvaniye transfer the rychazhkovy switch from the interior of a door to the situation LOCK.

After a zakhlopyvaniye unlocking from within back doors becomes possible only after a conclusion of their rychazhkovy switches from the situation LOCK. Forward doors can be open by means of internal handles.

For reasons of the general safety all doors of the car during movement should be blocked!

Back doors of the car are in addition equipped with the special blokirator, allowing to prevent possibility of their unlocking from within salon. These blokirator without fail should be used in transit children. For activation of a blokirator lower down a rychazhok located over a latch of the lock at a back end face of a door. Switching off of a blokirator is made by switching a rychazhka in the top situation.

Blokirator of the door lock, preventing possibility of its unlocking from within salon.

In case of failure do not forget that at the included blokirator back doors of the car can be open only outside - take care of that back passengers could get out during time of the car!

System of the electric uniform lock

Switches of management of activators of door locks

Management of activators of locks of all doors (including a back door) is made by means of the switches of keyboard type located on armrests driver's and forward passenger doors. For locking of locks press the right half of a key of the lock, for unlocking - on left.

Keyboard switch of management of door activators of the electric uniform lock.

Blocking of doors by means of switches or a remote control (DU) is not represented possible in the following cases:

  • The driver's door is open, and the key is not taken from the ignition lock.
  • The driver's door is open, and head headlights are not extinguished.

After blocking inclusion opening of back doors from within salon becomes possible only after an otpuskaniye of rychazhok of blokirator. Forward doors can be opened by means of internal handles.

Remote control by door activators of the uniform lock

By means of the DU panel of a door of the car can open at distance without key application.

DU panel activators of locks of doors.

The intake of the uniform lock is located in assembly of a lamp of illumination of salon, or in the central part of the top console. Having come nearer to the car on sufficient distance (about 3 m), direct the DU panel on the receiver and press, depending on an objective on the LOCK button (Locking) or UNLOCK (Unlocking) on its obverse panel.

Obstacle existence between the DU panel and the receiver of the uniform lock is capable to prevent operation of activators, in any case considerably reduces radius of operation of the panel. The average radius of action (in the absence of obstacles) DU makes about 3 m.

At the moment of DU panel use on its obverse panel the control lamp confirming sufficiency of level of a charge of its batteries should light up. Average service life of batteries makes one year then it is necessary to establish instead of sat down two new elements of the CR1616 type tension on 3 V.Pri performance of replacement watch observance of polarity of installation of elements (symbols «+» and «-» are engraved on their cases).

The DU panel is rather vulnerable knot and can be put out of action at sharp stirring. Do not drop the panel and do not throw a bunch of keys by which it is attached.

The intake of the uniform lock provides reception of signals (and operation on them door activators) several (to four) DU panels. For programming of panels for the purpose of use them on your car make the following procedures:

 PERFORMANCE ORDER

  1. Unlock a driver's door and leave it open on all the time of performance of programming of panels.
  2. Transfer a rychazhok of a mechanical drive of a blokirator of the lock to the situation LOCK.
  3. Insert a key into the lock of ignition and turn it in the situation RUN/ON (see an illustration).
  4. Within the next 20 seconds direct on the receiver the DU panel subject to programming and press the LOCK button on its obverse panel. Hold the button pressed not less than 5 seconds during which the electronic module of an intake will be adjusted on an alarm code of this panel and will confirm a successful conclusion of control with a way of operation of activators and unlockings of door locks.
  5. On termination of programming of the first panel, it is possible to prepare the receiver for reception of signals from additional (total number to 4). Within 20 seconds after completion of programming of the first panel transfer a rychazhok of a mechanical drive of a driver's door to the situation LOCK and repeat the described procedure for the following panel.
  6. To keep the entered codes in memory of the receiver, it is necessary within 20 seconds after completion of programming of the last panel to switch off and again to include ignition. During this moment all earlier written down codes will be replaced with the new.

At the moment of unlocking of door locks by activators of the uniform lock from the DU panel, and also when opening doors illumination of salon automatically joins. These lamps remain included during about 30 seconds, or till ignition inclusion (key turn in the situation ON - see an illustration).

Anticreeping alarm system

Sensitive sensors supervise a condition of doors (including a back door), a cowl, folding glass and in case of identification of signs of unauthorized penetration into the car provide inclusion of sound and visual alarm signals. Within the first 3 minutes the horn will publish buzz, and then head headlights and back marker lights will continue to blink within 15 minutes. Possibility of start of the engine will be blocked till system shutdown.

Turning on of the alarm system is made at operation on locking of doors of activators of the uniform lock (from keyboard switches or from the DU panel). After shutdown of 30-second illumination of salon (see the item. "At the moment of unlocking of door locks...") on the dashboard the control lamp of introduction in operation of the anticreeping alarm system starts to blink. The lamp will stop to blink about 15 seconds later, confirming a successful conclusion of installation of the alarm system. If a lamp during this period of time it is necessary to burn continuously, whether check densely the cowl is closed.

If the control lamp continues to burn continuously during using the car, address for consultation in dealer office of the Chrysler company.

If at the moment of unlocking of doors by a key or on a signal from the DU panel the horn publishes triple buzz, it means that in your absence the system of the anticreeping alarm system worked. Check, whether there are no signs of penetration into the car of extraneous persons.

The system of the anticreeping alarm system is conceived as vehicle means of protection. Nevertheless there are situations in which there is its failure. If, remaining in the car, you will casually make locking of doors by the keyboard switch or from the DU panel, the anticreeping alarm system will work in attempt of opening of a door from within for the handle. Involuntary shutdown of system occurs when unlocking by a key of a door of a back. After the door will be closed repeated initiation of the alarm system will not occur.

Activation of the anticreeping alarm system occurs at the moment of battery connection after completion of service or car repairs. Thus all external lighting devices turn on in a blinking mode, and ignition is blocked. Shutdown of system is made by key turn in the lock of any of doors, or at operation of activators of the uniform lock from the DU panel.

Systems of safety and restriction of movings of the driver and passengers

Safety of the persons which were in the car is one of the most important and responsible tasks of designers and developers. From the knots, urged to carry out this task seat belts of the driver, forward and back passengers, and also a safety cushion of the driver are main. Standard seat belts can be also used for fixing of special adaptations for transportation of babies and children of younger teenage age.

Pay close attention of information stated in this subsection is will help you to achieve the maximum return from the systems of safety equipped in the car.

Seat belts

General information

The violation of the rules of using seat belts repeatedly increases risk of receiving mutilations in case of emergency collision! Do not forget to fasten the seat belt and watch that all passengers who were in your car were fastened.

Remember that the wiped or torn belt at the moment of collision can tear, without having executed thereby the function. Regularly check a condition of tapes, buckles, anchor brackets and returnable devices of seat belts. The damaged components are subject to immediate replacement in knots of a standard design. Obligatory replacement of the worked belts should be made also after failure.

Of need of a pristegivaniye seat belts remind a control lamp on the car dashboard (see. Undressed Start of the engine and driving), and also an alarm buzzer.

Remember that a solid experience of driving in any a case does not grant the right to neglect use of seat belts. Be fastened even in case of a trip on very short distance. Do not forget that not all participants of traffic are the disciplined and skilled drivers, and therefore the probability of collision takes place constantly, both far from the house, and on your native street.

Pilot studies prove that use of seat belts allows to reduce repeatedly risk of death of the driver and passengers of a vehicle during collision. The most serious traumas usually turn out as a result of ejection of the person from car salon. It seat belts also allow to avoid, and therefore, each participant of movement, the driver or the passenger, should be reliably and is properly fastened.

Belts of universal type

General information

The zone section of a universal seat belt should be laid so that it covered the most powerful bones of a coxofemoral joint of a skeleton. The wrong putting on of a belt increases risk of a travmirovaniye in case of collision! Strictly follow the instructions provided below on putting on and a pristegivaniye of seat belts.

Pristegivaniye one belt at once two people it is inadmissible in view of considerable decrease in efficiency of action of a belt. Besides, during collision both passengers can suffer as a result of blow the friend about the friend!

The lobbies located near doors and back seats of the car are equipped with seat belts of universal type.

Each of universal belts consists of humeral and zone sections. Inertial type the returnable device provides belt blocking only at its sharp breakthrough (during emergency braking or collision). Thus the belt is freely taken up from a drum at its smooth pulling that allows to place conveniently it on a body of the driver/passenger.

Instructions for use universal seat belts

At a buckle zastegivaniye not on the clamp the belt will not provide to you due safety. The zone section of a belt can pass thus too highly, covering less strong bones of a skeleton. Watch, that the belt was always clasped in the lock next to your seat.

Too free placement of a belt is inadmissible also. At sharp braking the body will manage to get dostavochny for receiving traumas acceleration. Watch that the belt densely covered a trunk.

At all do not pass humeral section of a belt near at hand - thus also efficiency of its action considerably decreases. Throw a belt through a thorax so that the maximum loading at blow fell on the strongest bones of a skeleton.

Take the place in the car and close a door. Lean the elbows on a back and adjust a seat.

The buckle of a belt is located on a door rack directly over edge of a back of a seat. Grasp a buckle and extend a belt from the returnable device. Throw humeral section of a belt through a breast, and fast straighten on hips.

Extend a belt for a buckle from the returnable device.

If the length of a belt allows, latch a buckle in the mechanism of the lock of the clamp, located under a seat pillow from its opposite side.

Latch a buckle in the clamp lock.

Throw zone section of a belt through hips, at once under a stomach. To choose a weak point, pull for humeral section of a belt. For weakening of a belt incline a buckle and pull from itself fast section. Dense landing of a belt reduces risk of a proskalzyvaniye of a trunk under it at collision.

Too high laying of zone section of a belt is fraught with damage of an internal at failure. Watch that the main loading fell on the strongest coxofemoral bones!

The humeral section of a belt should settle down conveniently on a breast, without mentioning thus cervical department. The weak point will get out the returnable device automatically.

Perekruchivaniye of a belt can lead to cuts of soft fabrics of a trunk during strong blow at collision. Watch that the belt was constantly straightened on a breast and hips!

For release from a seat belt press the PRESS button of the lock of a clamp of a buckle. The belt will automatically be winded on a drum of the returnable device. In case of need shift a buckle down on a belt tape, having given the chance to it to be winded completely.

Pregnant women at a pristegivaniye of a seat belt should watch that its zone section settled down strictly on hips and not to allow a perekidyvaniye it through a stomach. In case of collision the main loading is necessary on powerful bones of the coxofemoral joint, best capable to protect a fruit.

At a pristegivaniye a universal belt of the teenager or the undersized passenger watch that it settled down in a seat vertically and periodically check density of laying of a belt.

Central zone belt of a back seat

At too weak tension of a zone belt or too high its laying the passenger during collision can slip under a belt and sustain injuries. Watch that the belt densely fitted hips, and the main loading in case of collision fell on strong bones of a coxofemoral belt of a skeleton.

The passenger sitting in the middle of a back seat should be fastened by specially provided zone seat belt. For a zastegivaniye of a belt latch a buckle in the clamp lock.

To extend a zone belt, incline its buckle and pull. Truncation of a belt is made by pulling up of the free end of a tape. Watch that the belt densely covered hips. Occupy convenient situation on a seat, densely nestle on a back and adjust length of a belt so that it densely covered your trunk.

Building of seat belts

Use of the extension piece of a seat belt without existence of strict need for it is dangerous! Apply the extension piece only when the full length of a standard belt does not suffice for a pristegivaniye of the stout passenger.

If the seat belt is too short for a pristegivaniye of the stout person, in dealer office of the Chrysler company it is possible to get the special extension piece, allowing to increase a belt till the demanded size. The extension piece should be used only when the length of a standard belt does not suffice. In other cases disconnect it and put in a ware box or a luggage compartment of the car.

Adaptations for transportation of babies and children of younger age

Designers of the Chrysler company developed special devices for transportation in the car of babies and children of younger age. At installation of these devices on standard seats of the car strictly follow instructions of their manufacturers. In case of need consult at specialists of dealer office.

Safety cushion

General information

Existence in the car of a safety cushion does not release the driver from need to use a seat belt. Excessively close stay to the helmsman of wheels during inclusion of a pillow is fraught with receiving traumas!

For effective operation of a pillow between a steering wheel and the driver there should be a sufficient free space. Sit down directly, conveniently put hands on a wheel, be fastened by a seat belt.

Cars of considered brand are equipped with a safety cushion of the driver. The block is built in in a nave of a steering wheel and in case of strong front blow provides instant with filling by gas of the pillow made of a dense material. Together with a seat belt and knee protection the pillow provides reliable protection of the driver at a head-on collision of the car.

The block of a safety cushion is built in in a nave of a steering wheel.

The system of a safety cushion is equipped with the control lamp built in in an instrument guard If the lamp does not light up at ignition inclusion, continues to burn after start of the engine or joins in movement time, the car should be driven away for performance of the corresponding diagnostics and necessary repair in a workshop of dealer office of the Chrysler company.

The main components of system of a safety cushion are: Blow sensors, the self-diagnostics Block, the Control lamp, the activation Module with the pillow fixed on it, the Steering wheel and a column of a special design, Connecting electroconducting and Knee protection (see an illustration below).

Knee protection (it is specified by shooters).

Functioning principle

Blow sensors

Sensors are located in a forward part of the car, and also in its salon and provide operation of the module of activation of a pillow when acceleration of face-to-face blow reaches a certain value. Sensors should not react on sliding, lateral and back blows, and also to a car perevorachivaniye. Inside sensors are equipped with the switches connected to the block of self-diagnostics of system and the module of activation of a pillow.

Self-diagnostics block

The block checks serviceability of functioning of electronic components of system each time at an ignition key povorachivaniye in the situation START or RUN/ON (see an illustration). Into number of such components enter all from listed in the item. "The main komponenty safety cushion systems...", except for a steering wheel, a column and knee protection.

At initial inclusion of ignition the block provides inclusion of a control lamp of a safety cushion on an instrument guard of the car for a while from 6 to 8 seconds. Then the lamp should go out. If at diagnostics performance in system any violations are revealed, the lamp will continue to burn continuously, or will pass to a blinking mode.

Activation/safety cushion module

The module is located in the central part of a steering wheel. When the acceleration arising at a head-on collision reaches sufficient value, sensors of blow give out a signal on module operations. Thus the gas generator of the module provides emission of a large amount of the nontoxical nitrogen, providing an instant naduvaniye of the pillow made of a strong material. The decorative cover in the central part of a steering wheel leans back and the pillow is developed, filling space between a wheel and a body of the driver. All process lasts about 50 milliseconds that corresponds to about a half of time spent by the person for blinking by eyelids. Almost at once nitrogen from a pillow is issued through the ventilating openings directed towards the dashboard, and therefore, operation of a pillow is not capable to prevent the driver in driving or to limit sector of its review.

Consequences of operation of a safety cushion

Once the worked safety cushion will not provide protection to the driver at repeated collision! The module should be replaced at the first possibility in dealer office of the Chrysler company.

It is not necessary to fix to the car knifes for a sgrebaniye of snow, the winch and other non-standard equipment which has not been provided by a design of a front. Installation of the such equipment it is capable to break serviceability of functioning of sensors of blow of system of a safety cushion!

Naduvaniye of a pillow is made almost instantly on a signal of sensors of the blow reacting to face-to-face acceleration of a certain force. Almost immediately the pillow is blown off.

Insufficiently strong face-to-face blow should not lead to pillow operation therefore it is not necessary to consider absence of reaction of system as a sign of its malfunction.

Operation of a safety cushion can have some collateral consequences:

  • Contact to nylon of a pillow of open sites of skin can lead to receiving the grazes similar on character, left on hands at the burns got at a friction about a kapron rope or as a result of sliding falling on a carpet in a gym. They do not speak at all contact to chemically hostile environment! Nevertheless it is not necessary to neglect medical assistance.
  • During production of nitrogen formation of the easy smoke actually representing the smallest particles of nontoxical by-products of a gazogeneratsiya is not excluded from a safety cushion. Contact of these particles to mucous membranes of a human body can cause the insignificant irritation which is easily removed at washing by pure cool water. For persheniye elimination in a throat or in a nose it is enough to leave salon on open air. In case of need address for the help to the doctor.
  • If after pillow operation the car is capable to continue movement, the sduty pillow should be combined and jostled in a cavity in a stupichny part of a steering wheel.

Service of system of a safety cushion

Any sort of updating of components of system of a safety cushion are capable to lead to refusal of its operation at the right time! Do not try to change laying of electroconducting of system or to fix a decorative cover in the central part of steering different column tapes and bandages. Do not make change to a design of a front of the car!

Under a steering column reliable protection of knees of the driver (see an illustration 1.48) should be established - at all do not fix on its panels any additional equipment and do not use them for storage of extraneous subjects!

At all do not undertake attempts of independent performance of repair any of system components! this work should be charged to specialists of dealer office of the Chrysler company.

Below the list of the reasons on which it is necessary to address to specialists of dealer office of the Chrysler company, understanding systems of safety cushions is provided:

  • The control lamp of a safety cushion does not light up on 6 ÷ 8 seconds at initial inclusion of ignition, or at once enters into a blinking mode.
  • The lamp continues to burn continuously or in a blinking mode after end (6 ÷ 8) the control period
  • The lamp joins on constantly, or in a blinking mode during car movement.

At refusal of a speedometer, a tachometer and measuring instruments of working parameters of the engine the module of activation of a safety cushion also fails. In such situation it is necessary to try to replace a safety lock No. 22 in the assembly block.

Adjustment of provision of seats

Performance of adjustment of provision of a driver's seat during movement of the car dangerously! At a sharp push it is easy to run away, besides it can easily appear correctness of laying of a seat belt is broken. Make adjustment of provision of a seat before a start of motion.

Forward seats with a manual drive (a standard complete set)

Correction of provision of a frame of a seat

To shift a seat at will forward or back, pull up the bracket of management located in front under its pillow. Release a bracket and, поерзав, make sure that the seat was reliably fixed in new situation.

Adjustment of provision of a frame of a forward seat (the arrow showed a management bracket).

Correction of an inclination of a back

During movement the back of a seat should not be cast away too strongly when the seat belt ceases to nestle on your breast as in this case at collision the belt will be not capable to hold a body already. To lean back on a seat it is recommended only during parking!

For correction of an inclination of a back of a seat lift located assembly under a seat pillow the lever and lean back together with a back in convenient situation. Return of a back to vertical situation occurs automatically at lever procrastination up.

Adjustment of an inclination of a back (the arrow showed a control lever).

Adjustment of height of provision of head restraints

Head restraints provide reliable protection of cervical department of a backbone in case of blow in the car behind. The head restraint is usually established in extreme top situation.

The head restraint should is established in extreme top situation.

Forward seats with the electric drive on six degrees of freedom (an additional complete set)

In order to avoid damage of components of the electric drive do not put under seats any subjects!

Control panels are located the electric drive on the outer side of a frame of each seat, is direct under its pillow.

Electrodriving forward seats.

Adjustment of height of provision of a seat is carried out by means of the central switch - turn its rychazhok respectively up or down.

For seat shift forward or turn the same rychazhok (central) respectively forward or back back.

The inclination of a back of a seat is corrected by means of the rychazhkovy switch A.

For correction of an inclination of a pillow use the switch B.

Folding back seat of separate type

Both lateral backs of a back seat develop that allows to expand essentially in case of need volume of a luggage compartment.

For simplification of procedure of folding of backs of a back seat, shift forward seats forward against the stop, and their backs transfer to vertical situation. The description of procedure of folding of a back seat below is provided.

Each of pillows of a back seat is equipped fixed in its back part special pedely, having pulled for which, the pillow can be lifted, having pressed to a back of a forward seat.

The pillow nestles closely on a back of a forward seat (on an insert location of a loop is shown).

For additional expansion of volume of a luggage compartment of a pillow of a back seat can be taken. Turn a pillow a floor a corner 45 °. If now to pull a pillow up, its arms will be liberated from the clamps and the pillow can be removed. Installation is made upside-down.

For removal of head restraints from backs of a back seat turn clockwise special blocking couplings. Now, to take a head restraint, it will pull vertically up from directing nests enough.

Head restraints of back seats are equipped with blocking couplings.

After extraction head restraints can be fixed in the special nests provided in combined pillows - nests are also equipped with the blocking couplings, head restraints reliably fixing probes.

Find from below from the outer side of the corresponding back of a seat a special control lever, delay the lever back and combine a back forward.

Location of the lever of an otpuskaniye of a back of a back seat.

For fixing of back universal seat belts at the combined back seat on their humeral sections and lateral panels of furnish of salon special clamps loopy крючкового type are provided.

For return of a back seat to an initial working condition lift its backs and latch them in vertical situation. If the cargo placed in a luggage compartment does not allow to lift completely a back, will return to a starting position a pillow inconveniently. The handle of the lock will not allow to plant completely a pillow - such safety lock guarantees stability of fixing of a back to a seat at adaptation installation on it for transportation of children.

Electrodriving window regulators

In order to avoid children's overindulgence the electric drive of window regulators functions only at the included ignition (a key in the situation ON/RUN). Each of lateral windows is equipped with the individual control panel with the switch of keyboard type. For lowering of glass it is necessary to press a key down, for lifting - up. The driver's door is equipped with the universal control panel, allowing to operate with window regulators of all door windows.

Control panel electric drive of window regulators.

Rear-view mirrors

Internal rear-view mirror

Internal rear-view mirror with manual switching in day and night provisions

The mirror should occupy such situation to provide the review precisely through the center of back glass of the car. By means of the rychazhkovy switch located in the lower part of the case of a mirror, the last can be transferred in day, or to night situation that allows to avoid dazzle of the driver by a driving beam of headlights of a vehicle overtaking the car. For transfer of a mirror to night situation delay a switch rychazhok on itself.

The lever of manual translation of a mirror in night situation.

Internal mirror with the automatic device of a priglusheniye of reflected light

Such mirror automatically reduces intensity of the reflected driving beam of head headlights of vehicles overtaking the car. Inclusion and switching off of the device is made by means of located from below on the case of a mirror of the button. At system activation in the button the control lamp lights up.

The button of turning on of the device of an automatic priglusheniye of intensity of reflected light.

External rear-view mirrors

General information

Cars and the other objects reflected in convex glass of the right mirror look smaller and remote than if glass was flat. Before making maneuver, being reconstructed in the right row check a road condition behind itself on an internal mirror, trying to rely not too on reflection in the right lateral!

Correctly adjusted lateral rear-view mirror should be directed precisely on the middle of the next lane and slightly block sector of the review of an internal mirror. Correction of provision of the mirror not equipped with the electric drive is made manually by a turn of a frame of its glass.

External mirrors with heating (an additional complete set)

A food on heating elements of mirrors moves at the same time with inclusion of heating of back glass.
External mirrors with the electric drive (an additional complete set)

The combined switch of management is located the electric drive of correction of provision of external rear-view mirrors at the left below on the car dashboard. For correction of provision of the left mirror establish the central rychazhok of the switch in situation L, right - in situation R. Adjustment of an inclination of mirrors is carried out by means of four command keys.

The combined switch of management of the electric drive of correction of provision of external rear-view mirrors.

Lever of an otpuskaniye of the lock of a cowl

Leaky closed cowl can unexpectedly open during car movement, having blocked the driver review sector! Watch that the lock latch reliably worked at a cowl zakhlopyvaniye.

For opening of a cowl pull on itself the lever A located at the left under the dashboard. Then leave the car, push a hand under slightly risen cowl and pull on itself the safety handle of a latch of V.Podnimite and prop up a cowl.

The lever of an otpuskaniye of the lock of a cowl in salon of the car (And) and the latch handle under a cowl (In).

At a podnimaniye of a cowl there is an automatic inclusion of a lamp of illumination of an impellent compartment.

Parking brake

Try not to leave children in the car without supervision. In advance warn them what to touch the lever of the parking brake, no less than the handle of gear shifting it is dangerous!

Do not lock children and pets in the car left on the sun - the probability of receiving a heatstroke is too great!

To cock the parking brake, strongly pull up the handle of the lever of its drive, located in the central console of the car between forward seats. If the parking brake is cocked at the included ignition, on an instrument guard the control lamp should light up.

The control lamp only confirms the fact of raising of the parking brake, in any way without reflecting the brake effort developed thus.

Before leaving parked on an inclined site of the road the car make sure of reliability of raising of the parking brake and do not forget to transfer AT to situation P / to include RKPP on the first transfer. Make sure that the transfer case is not in neutral situation, otherwise the car is not insured from a skatyvaniye under a bias regardless of the provision of transmission.

At a car parking on an inclined site of the road it is important to cock the parking brake earlier than to start AT switching in situation P, otherwise the mechanism of blocking of transmission it will appear under loading and the selector lever will need to be switched then to transfer.

Do not forget to cock without fail the parking brake before leaving the car.

For an otpuskaniye of the parking brake slightly pull the lever up, then press located in a face part of its handle the button and completely lower the lever down. Make sure that the control lamp on an instrument guard went out - movement with the cocked parking brake can lead to failure of brake mechanisms.

If the car is equipped with an automatic regulator of back brake mechanisms, originators of this Management do not recommend to the owner to make independently any adjustments - such responsible work should be charged to specialists of dealer office of the Chrysler company.

Recommendations about a running in of the new car

All necessary are made for normal operation of the car of setup of the engine industrially by specialists of the Chrysler company. In order that in the maximum degree to prolong service life of the car and to achieve high efficiency of return of the engine, throughout several hundred km/miles of run it is necessary to observe some special rules. The list of rules and restrictions which should be observed the period of a running in of the car is provided in below-mentioned points:

  • Regularly check level of cooling liquid and impellent oil. Try to reveal during time signs of an overheat of various components of the car. In a running in the engine tends to consume slightly more fuel and oils therefore be not upset insufficient profitability of their expense throughout the first 1 900 km (1 200 miles) run.
  • Before including transfer after start of the cold engine let's to it get warm within at least 15 seconds.
  • Throughout the first 160 km (100 miles) run avoid movement with a speed over 80 km/h (50 miles/h), further to a mark of 800 km (500 miles) in the counter of the odometer try not to gather speed over 88 km/h (55 miles/h). Avoid complete opening of a butterfly valve and try to reduce whenever possible the periods of operation of the engine on single turns.
  • In a running in the engine does not need filling by any special oil. There is no need as well performance of replacement of oil and the oil filter earlier, than it is stipulated by the schedule of routine maintenance of the car (see. Head of Control and routine maintenance). It is not necessary to add any additives as they can prevent normal extra earnings of piston rings in engine oil.

Car filling by fuel

For opening of the hatch of a jellied mouth of a fuel tank pull up the lever located on a floor of the car between a driver's seat and a threshold of the right door. On the lever there is an inscription of FUEL DOOR and the image of the fuel pump is put.

Lever of opening of the hatch of a jellied mouth of a fuel tank.

On a case of failure of the mechanism of a remote drive of unlocking of the hatch of a jellied mouth, in the back lateral panel of a body behind a spare wheel the special emergency cable is provided - open a cover and, having pulled a cable, open the hatch of a jellied mouth.

Cable of emergency opening of the hatch of a jellied mouth.

Muffle the engine and remove from a jellied mouth of a fuel tank a cover for what turn it counter-clockwise. Fix a cover in special, provided on back the parties of a door of the hatch, a clamp. For cover installation into place fill it in a mouth of a tank and tighten clockwise at least on three clicks.

Opening of a jellied mouth.

The full volume of a fuel tank makes 87.4 l.

The requirements shown to a grade of fuel

The design of power supply systems and engine management provides good profitability of fuel consumption in case of car filling by high-quality unleaded fuel.

Use for car filling only gasoline with octane number not below 87, determined by a method of calculation of arithmetic-mean value between the sizes defined research and motor ways: N= (R +М)/2, or, in Russian designations: N= (AI +А)/2.

Periodic emergence of an easy detonation in the engine at work it on low turns should not cause special concern. In case of a strong detonation on high turns it is necessary to address in dealer office of the Chrysler company.

Engine damages owing to a strong detonation do not get on protection of guarantee certificates.

Besides, that gasoline should be unleaded and have octane number not below the stipulated value, it is recommended to use the fuel containing such additives, as inhibitor of corrosion and means for increase of stability of turns of the engine. Application of such additives allows to increase efficiency of return of the engine and reduces its expense. Usually unleaded fuel of the class Premium already contains such additives.

Use of low-grade fuel can lead to emergence of such problems, as the complicated start of the engine, spontaneous it остановы and violation of stability of turns. In case of appearance of any of the listed symptoms, try to replace fuel brand before there will be more serious problems.

Some grades of fuel represent a combination of the unleaded gasoline mixed with such kislorodsoderzhashchy additives, as alcohol and methyl-tetrabutilovy (MTVE) and etil-tetrabutilovy (ETVE) air. Thus the importance has type and quantity of the oxidizer added to fuel. For filling of cars considered in this Management the following combinations are admissible:

  • Mixed with MTVE in the ratio not above 15/85 unleaded gasoline.
  • 17/83 (not above) ETVE mix with unleaded the combustible.
  • The mix containing 10 % an additive to gasoline of ethyl (drinking) alcohol.

Added to unleaded gasoline of methyl alcohol can vary from 3 % and above.

Use of the fuel containing methyl alcohol on cars of considered brand is inadmissible and can bring to difficulties at start of the engine and to failure of sensitive components of a power supply system!


The problems connected with use of fuel with additives of methyl alcohol do not get to the list of the refusals listed in guarantee certificates of the Chrysler company.

Control systems of the engine

General information

In order to avoid violation of serviceability of functioning of a power supply system try to observe the following rules:

  • Do not use for car filling having the raised content of lead etilirovanny gasoline. Violation of this requirement is fraught with decrease in efficiency of return of the engine, failure of components of systems of decrease in toxicity of the fulfilled gases, and also violation of guarantee certificates of the Chrysler company.
  • Some refusals of power supply systems and ignition can lead to an overheat of the catalytic converter. Emergence of a pungent smell of ashes and an easy smoke can be a symptom of demanding urgent repair of an engine failure. Try to contact representatives of dealer office of the Chrysler company immediately.
  • If operation of a vehicle assumes raised loads of the engine, and also at movement with a full load in the conditions of arid and hot climate it is necessary to fill the car with unleaded fuel of the class Premium, allowing to avoid a detonation. If the detonation nevertheless arises, try to lower load of the engine in order to avoid failure of pistons.
  • It is not recommended to add in additive fuel for increase of octane number of fuel - the most part of such additives contains methanol and is capable to lead to appreciable decrease in efficiency of return of the engine and violation of guarantee certificates of the Chrysler company.
  • Try not to inhale fulfilled gases of the engine - they contain extremely toxic monooxide of carbon (WITH), capable to bring to a serious poisoning of an organism. Do not allow long operation of the engine in the closed rooms. Suppress the engine during long parking. During short parking with working engine include on full capacity system of ventilation of salon.
  • Decrease in the content in the fulfilled WITH gases is promoted by a regularity of performance of procedures of routine maintenance of the car (see. Head of Control and routine maintenance). Through demanded intervals of a time/distance in kilometers lift the car over the earth and check a condition of components of system of production of the fulfilled gases. During time eliminate the revealed defects. At car operation with the damaged components of system of production of the fulfilled gases open all lateral windows and include on full capacity salon ventilation.
  • Before a start of motion check density of closing of a door of a back and its folding glass (at the corresponding complete set of the car).

Catalytic converter

Violation of service conditions of the engine can lead to failure of the expensive catalytic converter. In case of any disturbing symptoms, in particular such as admissions of ignition or decrease in efficiency of return of the engine it is necessary to make diagnostics and car service immediately. Further its operation can lead to failure of the catalytic converter!

The cars equipped with the catalytic converter are subject to filling by only unleaded fuel. The high content of lead in etilirovanny fuel is capable to lead to appreciable decrease in efficiency of the converter and its fast exit out of operation. Under usual service conditions of the car the catalytic converter does not need regular service. Nevertheless it is necessary to pay attention to observance of the correct settings of the engine.

Violation of the international plombirovka of adjusting devices of systems of decrease in toxicity is pursued by the law!

Do not park the car over easily flammable subjects, on the sites overgrown with a dry grass or filled-up fallen leaves.

At long operation of not adjusted engine there can be the characteristic pungent smell which is usually accompanying process of curing of rubber. This smell is a sign of a serious overheat of the catalytic converter. The car should be immediately stopped, the engine is muffled and cooled. Then without any delay it is necessary to make engine adjustment.

To minimize probability of failure of the catalytic converter try to observe the following rules:

  • Do not suppress the engine and do not interrupt an iskroobrazovaniye in cylinders at the transmission established on transfer, and also during car movement.
  • Do not start the engine by towage or car pushing.
  • Do not allow engine functioning on single turns with VV disconnected from a spark plug a wire.
  • Avoid long operation of the engine on single turns in case of violation of their stability.
  • Do not allow complete production of fuel containing in a fuel tank.