Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
- System of onboard electric equipment
   General information
   Diagnostics of malfunctions of electric equipment of the chassis - the general information
   Safety locks - the general information
   Fusible inserts - the general information
   Chain breakers (thermal relays) - the general information
   The relay - the general information
   Check of a condition and replacement of the breaker of indexes of turn / alarm system
   Check of serviceability of functioning and replacement of the universal podrulevy switch
   Check of a condition and replacement of the switch of the ignition/cylinder of the lock
   Check of serviceability of functioning of the switch of heating of glass of a door of a back
   Check of a condition and repair of a heater of glass of a door of a back
   Replacement of lamps of head headlights
   Adjustment of provision of head block headlights
   Removal and installation of cases of head block headlights
   Replacement of lamps
   Removal and installation of switches of head headlights and screen wiper of a window of a door of a back
   Removal and installation of a radio tape recorder and loudspeakers
   Removal and aerial installation
   Check of functioning and replacement of the motor of screen wipers
   Removal and installation of a combination of devices
   Check of functioning and horn replacement
   Description of a principle of functioning and diagnostics of a control system by speed (темпостата)
   Description of a principle of action and diagnostics of the electric drive of lowering-podnimaniya of glasses
   Principle of functioning and check of the central lock and system of opening of doors without a key
   Principle of action and check of serviceability of the electric drive of change of provision of seats
   Principle of action and check of serviceability of the electric drive of mirrors back look
   Safety cushion - the general information
   Electric circuits - the general information
   Arrangement and purpose of the relay and safety locks
+ Governing bodies and operation receptions


0ea6cc78 0ea6cc78

Check of a condition and replacement of the switch of the ignition/cylinder of the lock

All considered models are equipped with a safety cushion. The pillow constantly is in the "guarded" condition and can work to (be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receiving as a result of a trauma) each time at carrying out any works with components of system of safety disconnect a negative wire from the battery. After a wire detachment from the battery before starting to work wait at least two more minutes (the system is equipped with the condenser to which needs time for a discharge). In more detail about work of system of safety see. The section Safety cushion - the general information.

The lock of ignition is located on the right side of a steering column and fastens to it three sealed-up screws with heads of the TORX type (T-20) which otdavaniye needs the special tool (ask in shops of automobile accessories).

Check

Scheme of placement of plugs of the lock of ignition

Turned to the ignition lock сторогна the socket.


Wire nest
Color of a wire
To a chain
1
The yellow-dark blue
Starter relay
2
The yellow
Ignition/start
3
The gray-black
Control lamp of braking
4
The red-white
Battery food
5
The orange-black
Consumers in the position "RUN" of the lock
6
The violet
Consumers in the situation "RUN" and "ACC"
7
The pink-black
Battery food

 PERFORMANCE ORDER

  1. Remove the lock (see item 1-3).
  2. By means of an ohmmeter or equipped own battery of a lamp sampler check a continuity between lock plugs.
  3. If spetsifikatsionny requirements to a continuity on the switch (lock) of ignition are not satisfied, replace it.

Replacement

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Remove the top and bottom covers of a casing of a steering column (Head the Body).
  3. Give the sealed-up screws, separate the ignition lock from a steering column, then disunite the electric socket and remove the lock from a column.

The lock of ignition fastens by means of three sealed-up screws with heads of the TORX type (arrow) (the bottom screw is located under a cover).

  1. In case of need removals of the cylinder of the lock insert the ignition key and turn it in the situation LOCK. On models to 1994 (inclusive) вып. press a fixing pin a small screw-driver so that it appeared aflush with a surface. On models of 1995 вып. instead of a fixing pin the sealed-up screw which for release of the cylinder it is necessary to give is established.
  1. Press a fixing pin for liberation of the cylinder of the lock - on models of 1995 вып. give the sealed-up screw.
  1. Turn a key clockwise in the situation OFF that will allow to liberate the lock cylinder, however yet it is not necessary to remove the last finally.
  1. After liberation the cylinder should leave the lock approximately on 3 mm - do not try to take it before the key will be turned in the situation LOCK and taken from the lock.
  1. Installation make upside-down. After switch gearing with draft ползуна parking make sure that the lock tag of a column on the switch is located parallel to the electric socket.
  1. Before installation make sure that the lock tag of a column on the lock rose parallel to the electric socket.
  1. Insert the cylinder in the situation LOCK against the stop into a lock bottom. Pressing the cylinder, insert into it a key and turn it clockwise in the situation RUN. On models of 1995 вып. screw the sealed-up screw.