Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross-section stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross-section jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross-section jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Condition check, removal and installation of a steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions


0ea6cc78 0ea6cc78

Removal and installation of screw springs of a forward suspension bracket

Removal

 PERFORMANCE ORDER

  1. Weaken nuts of fastening of wheels, поддомкратьте a front of the car and establish it on props. Remove wheels.
  2. Mark situation and disconnect the forward driveshaft from the holder of a crosspiece of a leading gear wheel of differential (Head Coupling and the transmission line), then tie up a shaft aside a piece of a wire.
  3. Prop up bridge assembly by a jack got under differential or that is more preferable, two jacks - on one from each of the sides of the bridge (the last way will provide the best balancing). To Otboltita from the bridge the bottom levers of a suspension bracket (The section Removal and installation of levers of a forward suspension bracket).
  4. To Otboltita connecting links (racks) of the stabilizer and suspension bracket shock-absorbers from the forward bridge (The sections Removal and installation of the forward stabilizer of cross-section stability and its plugs and Removal and installation of forward shock-absorbers).
  5. Disconnect from a bridge arm a jet bar (The section Removal and installation of a cross-section jet bar of a forward suspension bracket).
  6. Disconnect average steering draft from a soshka of the steering mechanism (The section condition Check, removal and installation of a steering drive).
  7. Slowly omit bridge assembly so that springs were completely stretched. If the bridge is propped up only by one jack, ask the assistant to support in the course of lowering of the bridge its right edge. Remove the holder of a spring and take a spring from under the car.
  1. Details of fixture of a screw spring - after the spring will be completely stretched give a bolt and remove the holder, then take a spring through space between the bridge and a frame.
  1. Check a spring on existence of defects and traces of the corrosion, capable to be at the bottom of a premature exit it out of operation.

Installation

 PERFORMANCE ORDER

  1. Establish a screw spring on a bridge case, impose the holder on the bottom round of a spring and strongly tighten a bolt of fastening of the holder.
  2. Lift the bridge in adjusting situation and connect to its case the bottom levers of a suspension bracket (The section Removal and installation of levers of a forward suspension bracket). Tighten fixture with demanded effort.
  3. Connect average steering bent for to a soshka of the steering mechanism (The section condition Check, removal and installation of a steering drive).
  4. Fix a jet bar in the arm on the bridge (The section Removal and installation of a cross-section jet bar of a forward suspension bracket).
  5. Connect to a forward part of a case of the bridge of a rack of the stabilizer and shock-absorbers (The sections Removal and installation of the forward stabilizer of cross-section stability and its plugs and Removal and installation of forward shock-absorbers).
  6. Connect the forward driveshaft to the holder of a crosspiece of a leading gear wheel of differential (Head Coupling and the transmission line).
  7. Establish wheels and nuts of their fastening, then lower the car on the earth. Tighten nuts of fastening of wheels with demanded effort (see. Specifications to Head of Control and routine maintenance).