Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross-section stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross-section jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross-section jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Condition check, removal and installation of a steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions
0ea6cc78 0ea6cc78


Removal and installation of the pump of system of hydrostrengthening of a wheel

Components of the pump of system of hydrostrengthening of a wheel and its arms (V8) engine.

Components of the pump of system of hydrostrengthening of a wheel and its arms (the 6-cylinder engine)


 PERFORMANCE ORDER

  1. Weaken a tension of a driving belt and remove a belt from a pump pulley (Head of Control and routine maintenance).
  2. By means of a syringe suck away from the tank of system of hydrostrengthening of a wheel probably more liquid. Establish drain capacity under the pump and disconnect from it high-pressure head and returnable hydraulic lines. For improvement of access to a hose of the returnable line probably it is required to remove an air purifier casing (Head of the Power supply system and production of the fulfilled gases). To Zakuporta the open ends of lines in order to avoid leakages of liquid and hit in dirt system.

Shtutsernye of connection of tubes and hoses of hydraulic lines of the pump.

  1. Give forward fixing bolts both back fixing bolts and nuts, then remove the pump from the engine.
  2. In case of need removals from the pulley pump at first measure vystupaniye size from its nave of a shaft of the pump. Remove a pulley from a shaft by means of a special stripper (for pulleys of pumps of systems of hydrostrengthening) - ask in shops of automobile accessories.

For removal of pulleys of pumps of system of hydrostrengthening of a wheel the stripper of such design is issued - ask in shops of automobile accessories.

  1. For landing of a pulley to a pump shaft the special tool, however from a long bolt, a nut, a washer and a replaceable face head of the same also is issued this time that the nave of a pulley of diameter can be independently made its equivalent. Pull a pulley on a shaft so that the shaft acted over its nave on the same size that before dismantle.
  1. For pulley putting on on a pump shaft the special tool also is issued, but …

… this time it can make replacement, having taken for this purpose a long bolt with the same step of a carving, as a carving in an end face of a shaft of the pump, a nut, a washer and a replaceable face head of the same external diameter, as a shaft nave.

  1. Installation make upside-down. On termination of works do not forget to pump over system of hydrostrengthening of a wheel (The section Pumping of system of hydrostrengthening of a wheel).