Jeep Grandee Cheroki + Jeep Grand Cherokee brand Cars + Settings and routine maintenance + Ryadny six-cylinder engine + V8 Engine + Procedures of the general and major maintenance of the engine + Systems of cooling, heating and air conditioning + the Power supply system and production of the fulfilled gases + System of electric equipment of the engine + Systems of decrease in toxicity of the fulfilled gases and engine management + Manual box of gear shifting + Automatic transmission + Transfer case + Coupling and transmission line + Brake system - Suspension bracket and steering General information Removal and installation of the forward stabilizer of cross-section stability and its plugs Removal and installation of forward shock-absorbers Removal and installation of a cross-section jet bar of a forward suspension bracket Removal and installation of levers of a forward suspension bracket Removal and installation of screw springs of a forward suspension bracket Removal and installation of rotary fists Replacement of spherical hinges Removal and installation of a bar of the back stabilizer of cross-section stability Removal and installation of back shock-absorbers Removal and installation of a cross-section jet bar of a back suspension bracket Removal and installation of levers of a back suspension bracket Removal and installation of screw springs of a back suspension bracket Removal and installation of a steering wheel Condition check, removal and installation of a steering drive Removal and installation of the steering mechanism Removal and installation of the pump of system of hydrostrengthening of a wheel Pumping of system of hydrostrengthening of a wheel Wheels and tires - the general information Corners of installation of forward wheels - the general information + Body + System of onboard electric equipment + Governing bodies and operation receptions
|
Removal and installation of the steering mechanism
|
Take care of that the steering shaft was not turned at the removed steering mechanism as it can lead to safety cushion damage. One of ways of blocking of a shaft is the key povorachivaniye in the ignition lock in the situation LOCK. It is possible to pass also a seat belt through a steering wheel and to latch its buckle. |
Removal
|
- To Poddomkratta a car front also establish it on props. Cock the parking brake.
- Establish drain capacity under a case of the steering mechanism (only for the mechanisms equipped with the hydraulic booster). Disconnect hoses/tube of hydraulic lines and закупорьте the open ends for the purpose of minimization of losses of liquid and hit in system of pollution. In case of that existence, use for a detachment of lines a special key for cap nuts.
- Mark position of the bottom kardanny hinge of an intermediate shaft in relation to primary shaft of the steering mechanism. Remove the bottom coupling bolt of an intermediate shaft.
|
- Weaken nuts of these shtutserny connections (arrow) and disconnect lines of system of hydrostrengthening of a wheel from a box of the steering mechanism, then mark position of the kardanny hinge of an intermediate shaft in relation to primary shaft of the steering mechanism and weaken a coupling bolt.
|
- Give a nut of fastening of a soshka of the steering mechanism, remove a washer. Mark the provision of a soshka in relation to a shaft - at installation it should be strictly observed.
|
- Before removal of a soshka mark its situation in relation to a shaft of the steering mechanism.
|
- By means of a dvukhzakhvatny stripper separate a soshka from a shaft of the steering mechanism.
|
- For separation of a soshka from a shaft of the steering mechanism use a stripper.
|
- Holding the steering mechanism, give bolts of its fastening. Lower the block, disconnecting an intermediate shaft from primary shaft of the steering mechanism. Remove the steering mechanism from the car.
|
The steering mechanism fastens to a frame longeron by means of three bolts (arrow).
|
|
|
Installation
|
- Lift the steering mechanism in adjusting situation and connect an intermediate shaft, having tracked correctness of combination of labels.
- Establish fixing bolts with washers. Tighten bolts with demanded effort.
- Put on a shaft a soshka. Make sure of correctness of combination of labels. Establish a washer with a nut and tighten the last with demanded effort.
- Establish the bottom coupling bolt of an intermediate shaft and tighten it with demanded effort.
- Connect to a case of the steering mechanism of hoses/tube of hydraulic lines and add in the tank of system of hydrostrengthening necessary amount of liquid of a demanded grade (see. Specifications to Head of Control and routine maintenance).
- Lower the car and pump over steering system (The section Pumping of system of hydrostrengthening of a wheel).
|
|
|
|