Jeep Grandee Cheroki + Jeep Grand Cherokee brand Cars + Settings and routine maintenance + Ryadny six-cylinder engine + V8 Engine + Procedures of the general and major maintenance of the engine + Systems of cooling, heating and air conditioning + the Power supply system and production of the fulfilled gases + System of electric equipment of the engine + Systems of decrease in toxicity of the fulfilled gases and engine management + Manual box of gear shifting + Automatic transmission + Transfer case + Coupling and transmission line + Brake system - Suspension bracket and steering General information Removal and installation of the forward stabilizer of cross-section stability and its plugs Removal and installation of forward shock-absorbers Removal and installation of a cross-section jet bar of a forward suspension bracket Removal and installation of levers of a forward suspension bracket Removal and installation of screw springs of a forward suspension bracket Removal and installation of rotary fists Replacement of spherical hinges Removal and installation of a bar of the back stabilizer of cross-section stability Removal and installation of back shock-absorbers Removal and installation of a cross-section jet bar of a back suspension bracket Removal and installation of levers of a back suspension bracket Removal and installation of screw springs of a back suspension bracket Removal and installation of a steering wheel Condition check, removal and installation of a steering drive Removal and installation of the steering mechanism Removal and installation of the pump of system of hydrostrengthening of a wheel Pumping of system of hydrostrengthening of a wheel Wheels and tires - the general information Corners of installation of forward wheels - the general information + Body + System of onboard electric equipment + Governing bodies and operation receptions
|
Removal and installation of a steering wheel
|
All considered models are equipped with a safety cushion. The pillow constantly is in the "guarded" condition and can work to (be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receiving as a result of a trauma) each time at carrying out any works with components of system of safety disconnect a negative wire from the battery. After a wire detachment from the battery before starting to work wait at least two more minutes (the system is equipped with the condenser to which needs time for a discharge). In more detail about work of system of safety see. Head System of onboard electric equipment. |
|
- Establish operated wheels of the car rectilinearly. Disconnect a negative wire from the battery.
|
If the audiosystem of your car is equipped with a security code before disconnecting a negative wire from the battery make sure that you have that for system input in action after completion of works. |
- Give four fixing nuts and disconnect the safety cushion module from a steering column. Disunite the electric socket of the module. At work with the module always hold it the open party from own body. Always put the module on a workbench or other surface the open party up (at all down!).
|
- For removal of the module of a safety cushion give the top nuts (right top nuts occupies the same situation from the opposite side of a steering wheel).
|
|
… and the bottom nuts (the right is located similarly from the opposite side from a steering wheel).
|
|
- Release lock uvulas and disunite the electric socket of the module of a safety cushion.
|
- Give a nut of fastening of a steering wheel, then mark the provision of a steering shaft on the relation to a nave (if such labels are not put not so or if they are not combined) for the purpose of simplification of the subsequent assembly.
|
Do not allow a provorachivaniye of a steering shaft after removal of a steering wheel.
|
|
- Before removal of a steering wheel make sure of combination of adjusting labels on its nave and a pin of a shaft of a column (if those are available); if labels are absent, put them independently by means of a chertilka or white paint.
|
- By means of a stripper remove a steering wheel from a shaft. At all it is not necessary to force down a wheel from a shaft a hammer.
|
- Remove a steering wheel from a shaft only by means of a stripper AT ALL SBIVYTE IT the HAMMER!
|
- If the provision of operated wheels during performance of procedure did not change (they remained are directed rectilinearly), now it is possible to establish a steering wheel into place. If wheels turned, it is necessary to make centering of a spiral spring of a safety cushion. For this purpose establish forward wheels strictly rectilinearly and rotate a rotor of an hour spring clockwise against the stop (it is not necessary to make too big efforts). Now turn a rotor on two and a half turns counter-clockwise. In this provision of a wire of a horn there should be above, and wires of the module of a pillow - below.
|
Details of an hour spring of a safety cushion.
|
- For installation of a steering wheel achieve combination of adjusting labels on its nave and a shaft pin. Establish a nut and tighten it with demanded effort.
- Establish into place the safety cushion module. Screw four fixing nuts and tighten them with demanded effort.
- Connect a wire to the negative plug of the battery
|
|
|
|