Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information
   Replacement of blocks of disk brake mechanisms
   Removal, major maintenance and installation of a support of the disk brake mechanism
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms
   Removal, major maintenance and installation of wheel cylinders
   Removal and installation of the combined valve (regulator)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake hoses and lines
   Pumping of brake system
   Functioning check, removal and installation of the vacuum amplifier of brakes
   Functioning check, removal, installation and adjustment of the sensor switch of stoplights
   Adjustment of the parking brake
   Replacement of cables of a drive of the parking brake
   Replacement of boots of the parking brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions


0ea6cc78 0ea6cc78

Replacement of cables of a drive of the parking brake

All considered models are equipped with a safety cushion. The pillow constantly is in the "guarded" condition and can work to (be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receiving as a result of a trauma) each time at carrying out any works with components of system of safety turn the ignition key in the situation LOCK and disconnect a negative wire from the battery. After a wire detachment from the battery before starting to work wait at least two more minutes (the system is equipped with the condenser to which needs time for a discharge). In more detail about work of system of safety see. Head System of onboard electric equipment.

Forward cable

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.

If the autoradio tape recorder on your car is equipped with a security code before disconnecting from the battery a negative wire make sure available of your order of a code of connection of a radio tape recorder. Remove the floor console (Head the Body).

  1. Release the parking brake. Weaken nuts of fastening of back wheels, поддомкратьте a back of the car and establish it on props.
  2. Remove an adjusting nut of a forward cable (see an illustration), then disconnect a forward cable from the balance weight.
  3. Release a clamp of a forward cable, then take out an insert from the floor panel.
  1. For a detachment of a forward cable from its arm compress a clamp (shooter) by means of a small shlangovy collar of worm type.
  1. For extraction of an insert of a cable from the panel of a floor release lock uvulas (shooters) by means of a screw-driver.
  1. In salon of the car disunite electric sockets of the sensor switch of the parking brake and the safety cushion module (in a forward part of the module two electric sockets are located).
  1. For removal of the lever of the parking brake disunite the electric socket of the sensor switch of the parking brake (the central arrow) and give bolts of fastening of the lever (the left and right arrows).
  1. Give fixing bolts and remove the safety cushion module, having shifted it aside for ensuring access to the lever of the parking brake.
  1. For removal of the module of a safety cushion give four fixing bolts (arrow), lift the module up and disunite two its electric sockets (the second in a picture is not visible).
  1. Give bolts of fastening of the lever of the parking brake, remove assembly of the lever and overturn it upside down for ensuring access to a driving cable.
  2. Disconnect a cable of the parking brake from the lever and stretch it through the floor panel.
  3. Remove an insert of the panel of a floor from an old cable and put on it the new.
  4. Installation make upside-down.
  5. On termination of works do not forget to make cable adjustment (The section Adjustment of the parking brake).

Back cable

 PERFORMANCE ORDER

  1. On models with drum-type back brake mechanisms remove back wheels. To Poddomkratta the car also establish it on props.
  2. Disconnect a cable from the balance weight and liberate it from an arm at once behind the balance weight (see an illustration).
  3. Liberate a cable from clips on elements of a body and the car chassis.
  4. On models with drum-type back brake mechanisms remove brake drums, remove a back boot of the brake mechanism (The section Replacement of boots of drum-type brake mechanisms) and disconnect from it a cable. Compress a cable clamp a shlangovy collar of worm type and remove it, having passed through a board of the brake mechanism.
  5. On models with disk back brakes disconnect an ear a loop from the executive lever, then compress a clamp of fastening of a cable in an arm on a support.
  6. Installation make upside-down.
  7. On termination of works do not forget to make cable adjustment (The section Adjustment of the parking brake).