Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information
   Replacement of blocks of disk brake mechanisms
   Removal, major maintenance and installation of a support of the disk brake mechanism
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms
   Removal, major maintenance and installation of wheel cylinders
   Removal and installation of the combined valve (regulator)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake hoses and lines
   Pumping of brake system
   Functioning check, removal and installation of the vacuum amplifier of brakes
   Functioning check, removal, installation and adjustment of the sensor switch of stoplights
   Adjustment of the parking brake
   Replacement of cables of a drive of the parking brake
   Replacement of boots of the parking brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions


0ea6cc78 0ea6cc78

Functioning check, removal and installation of the vacuum amplifier of brakes

Components of assembly of the vacuum amplifier of brakes (the model since 1994 вып is shown. - on models of 1993 вып. instead of a lock ring on a finger of a bar of a pusher the clip) is applied

Functioning check

 PERFORMANCE ORDER

  1. Several times squeeze out a brake pedal at the switched-off engine and make sure of lack of a difference in size of reverse motion of a pedal at each muscleman.
  2. Squeeze out a pedal and start the engine. If thus the pedal fails a little more, the amplifier functions normally.

Tightness check

 PERFORMANCE ORDER

  1. Start the engine, later few minutes switch off it. Several times slowly squeeze out a brake pedal. If the pedal fails with each pressing ever less, sealing of the amplifier in norm.
  2. Squeeze out a pedal at the working engine, then muffle it without releasing a pedal. If changes in size of reverse motion of a pedal after its keeping squeezed out within 30 seconds will not occur, sealing of the amplifier in norm.

Removal

 PERFORMANCE ORDER

  1. Disunite the electric socket of the sensor of a course of a brake pedal.
  1. On models 1993 and 1994 of вып. disunite the electric socket of the sensor of a course of a pedal of a brake.
  1. To Otboltita the main brake cylinder from the block of the vacuum amplifier of brakes (The section Removal and installation of the combined valve (regulator)) and carefully delay the cylinder forward.
  2. Disconnect from the vacuum amplifier a vacuum hose of the inlet pipeline.
  3. By means of a small lamp find back (turned to a pedal) the end of a pusher of the amplifier. This end of a pusher fastens to the top part of a pedal of a brake by means of a small finger.
  4. Remove a fixing clip (models of 1993 вып.) or a lock ring with the flat and goffered washers (models since 1994 вып.) also take a finger from a pusher. Disunite the electric socket of the switch of stoplights.
  5. Give four fixing nuts and remove the amplifier from a partition of an impellent compartment. Nuts are under the dashboard and for simplification of performance of a task it is necessary to use a small lamp (see an illustration).
  6. Take away the amplifier from a partition so that hairpins completely left fixing openings, then take the amplifier together with arms and laying from an impellent compartment.

Installation

Installation make upside-down. Nuts of fastening of the amplifier tighten with demanded effort.