Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
- Automatic transmission
   General information
   Diagnostics of malfunctions - the general information
   Removal and installation of the lever of switching
   Check of a condition and adjustment of a cable of switching
   The description, replacement and adjustment of a cable of a drive of a butterfly valve in a mode kik-Down (TV cable)
   Serviceability check, adjustment and replacement of the sensor switch of permission of start
   Adjustment of a cable of a lay blokirator
   Check of a condition and replacement of a support of transmission
   Epiploon replacement
   Design description, removal and installation of lines and hoses of cooling of transmission
   Removal and installation of an additional cooler
   Removal and installation of automatic transmission
   Replacement of the module of management with transmission (TSM) (only for AW-4 and 42RЕ)
   Diagnostics of system of electronic control by automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions


0ea6cc78 0ea6cc78

Removal and installation of automatic transmission

Removal

The scheme of transfer of rotation of transmission (AW-4) (see requirements of Specifications to efforts of a tightening of carving connections)

The scheme of transfer of rotation of transmission (42RЕ) (see requirements of Specifications to efforts of a tightening of carving connections)

The scheme of transfer of rotation of transmission (42RH/46RH) (see requirements of Specifications to efforts of a tightening of carving connections)


Okhladitelnye lines of transmission are equipped with shtutserny sockets of fast joining which rassoyedineniye needs use of the special tool. Take care of existence such near at hand before starting to work (see the section the design Description, removal and installation of lines and hoses of cooling of transmission).


 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. On models of 1993 вып., equipped with transmission AW-4 remove the top half of a tube of a jellied mouth of transmission.
  1. On models of 1993 вып., equipped with transmission AW-4 remove the top half of a tube of the gulf of liquid.
  1. To Poddomkratta the car also establish it on props.
  2. Remove a zanosny plate (if that is provided).
  3. Disunite electric sockets, liberate plaits of wires from the clips on transmission and/or a transfer case and shift them aside. It will be reasonable to mark previously all wires for the purpose of providing a guarantee of their correct connection at assembly. On various transmissions various plaits can be used:
    • AW-4: VSS, sensor switch of permission of start and blocking electromagnet.
    • 42RЕ: VSS, electromagnet of transmission of the sensor switch of permission of start and blocking electromagnet; also the sensor of turns of a secondary shaft (only for 4WD models).
    • 42RH/46RH: VSS, sensor switch of permission of start and blocking electromagnet.
  1. Disunite electric sockets and liberate from clips on transmission and/or a transfer case plaits of wires; clean plaits aside; it will be reasonable to mark previously all sockets for simplification of the correct assembly).
  1. Carefully mark and disconnect all vacuum lines of transmission and/or a transfer case.
  2. Remove components of system of production of the fulfilled gases, disturbing to performance of the forthcoming work (Head of the Power supply system and production of the fulfilled gases).
  3. Merge transmission liquid.
  4. Establish into place the pallet of a case of transmission.
  5. Disconnect hoses and tubes of lines of a cooler of transmission (Undressed the design Description, removal and installation of lines and hoses of cooling of transmission). To Zakuporta the open ends of lines/unions in order to avoid hit in dirt transmission.
  6. Disconnect a driving cable of gear shifting from transmission (The section Check of a condition and adjustment of a cable of switching), shift it aside and fix on the pallet of a case of transmission.
  7. Disconnect from transmission a TV cable (The section Description, replacement and adjustment of a cable of a drive of a butterfly valve in a mode kik-Down (TV cable)), shift it aside and fix on the pallet.
  8. On 4WD models disconnect draft of switching of a transfer case from the lever of switching of modes on a box (Head the Transfer case).
  9. Prop up transmission by a jack - preferably use of a jack of special type. Safety chains of such jack will help to fix reliably on it transmission.
  10. Give bolts/nut of fastening of a back support of transmission to a cross-section beam. Slightly raise transmission with a transfer case, then give bolts of fastening of a beam to a car frame. Remove a cross-section beam.
  1. For a transmission detachment from a cross-section beam give a big central bolt (shooter).
  1. Slightly raise transmission and a transfer case (if it is equipped), then give three bolts (arrow) of fastening of the left side of a cross-section beam to a frame.

… give two bolts (arrow) of fastening of the right side of a cross-section beam to a frame and remove a beam.

  1. On all-wheel drive models remove a transfer case (Head the Transfer case).

If you do not plan to make transmission replacement, and remove it only for ensuring access to other components, such as the rotation converter, real need for removal of a transfer case is absent. However, it is necessary to notice that transmission removal assembled with a transfer case is much more difficult procedure, than their removal separately.


If you decided to leave a transfer case attached to transmission, take care of existence of safety chains for block fastening on a jack head. Transmission falling / a transfer case from a jack is fraught with the most serious consequences, up to an exit of components out of operation and receiving personal mutilations.

  1. Remove from transmission a cover of access to the rotation converter. On some models for its fastening three bolts, on others - three are used.
  2. Remove a starter (Head System of electric equipment of the engine).
  3. Mark position of the converter of rotation in relation to a driving disk for a guarantee of their correct installation at assembly (use white paint or a marker).
  1. Mark position of the converter of rotation in relation to a driving disk for the purpose of their correct installation at assembly - this factor makes essential impact on observance of balancing of the engine!
  1. Give bolts of fastening of the converter to a driving disk. For ensuring access to each of them turn a cranked shaft (only clockwise at the sight of in front).
  1. For ensuring access to each of bolts of fastening of the converter of rotation to a driving disk in the course of their otdavaniye turn a cranked shaft clockwise (at a view of the engine in front).
  1. Hang out the engine by means of a telezhechny jack or the winch (Head Ryadny the six-cylinder engine).
  2. Give the bottom bolts of fastening of transmission to the engine.
  3. Slightly omit transmission (and, on 4WD models, a transfer case if it was not disconnected) and give the top bolts of fastening of transmission to the engine.
  4. Disunite the electric socket and remove the sensor of provision of a cranked shaft (The head of System of decrease in toxicity of the fulfilled gases and engine management).

If to leave the sensor on the engine block, at removal (installation) of transmission it is easy for damaging.

  1. Lift the receiver щупа measurements of level of transmission liquid (see illustrations the Scheme of transfer of rotation of transmission (AW-4), the Scheme of transfer of rotation of transmission (42RЕ) or the Scheme of transfer of rotation of transmission (42RH/46RH)). Remove and throw out a sealing ring of a tube щупа.
  2. Shift transmission back, removing it from directing pins on the engine. Previously make sure that the converter of rotation is disconnected from a driving disk. Fix the converter in transmission in order to avoid its loss at removal of the last.
  3. Omit transmission and take it from under the car.

Installation

 PERFORMANCE ORDER

  1. Before installation make sure that the nave of the converter of rotation is reliably joined with the pump.
  2. Having fixed transmission (and on 4WD models and a transfer case if it on the former is attached to transmission) on a jack, lift it in adjusting situation. Try to hold transmission horizontally that it was not slipped out by the rotation converter. Connect lines of a cooler of transmission liquid.
  3. Turn the rotation converter, achieving combination of adjusting labels on it and on a driving disk (item 6).
  4. Carefully advance transmission (with a transfer case if it is connected - on 4WD models) forward until there will be a joining of directing pins to the rotation converter.
  5. Insert bolts of fastening of a case of transmission to the engine. Be verified with data of an illustrative material (see illustrations the Scheme of transfer of rotation of transmission (AW-4), the Scheme of transfer of rotation of transmission (42RЕ) or the Scheme of transfer of rotation of transmission (42RH/46RH)). Tighten bolts with demanded effort.
  6. Establish bolts of fastening of the converter of rotation to a driving disk. Tighten bolts with demanded effort (see. Specifications to this Chapter). Establish a cover of access to the converter, having strongly tightened its bolts.

If for fastening of the converter use new bolts, compare their length (measured from the bottom cut of a head till the end of a carving part) to the values given in Specifications. Application of bolts of excessive length is fraught with damage of surfaces of the converter.

  1. Establish bolts of fastening of a back support of transmission to a cross-section beam and bolts of fastening of a beam to a frame. Strongly tighten bolts.
  2. Remove the jacks holding transmission (with a transfer case if it is connected - on 4WD models).
  3. Establish into place a tube щупа measurements of transmission liquid.
  4. If separated a transfer case from transmission at removal, join them now (Head the Transfer case).
  5. Establish into place a starter (Head System of electric equipment of the engine).
  6. Connect a vacuum hose (and) and electric sockets and fix plaits of wires in clips.
  7. Connect a cable of a drive of a choice of transfers (The section Check of a condition and adjustment of a cable of switching) and a TV cable (The section Description, replacement and adjustment of a cable of a drive of a butterfly valve in a mode kik-Down (TV cable)). On 4WD models connect draft of switching for a transfer case (Head the Transfer case).
  8. Establish into place the driveshaft (ы) (Head Coupling and the transmission line).
  9. Establish acting in film components of system of release.
  10. Clean jacks and lower the car on the earth.
  11. Fill in in transmission liquid of a demanded grade (Head of Control and routine maintenance), start the engine and check it on leaks.
  12. Make adjustment of a cable of gear shifting (The section Check of a condition and adjustment of a cable of switching) and a TV cable (The section Description, replacement and adjustment of a cable of a drive of a butterfly valve in a mode kik-Down (TV cable)). On all-wheel drive models adjust also draft of switching (Head the Transfer case).
  13. Make trial runs, having made sure of serviceability of functioning of all knots.